It is a stressful task to buy a new boiler. It warms your home and gives you hot water. Replacing a new boiler would be a stressful task, but one you shouldn’t have to do. This is the handbook that will enable you to fit a boiler. Provided you stick to the steps, you can rest assured that there isn’t an issue, and you can sit back and enjoy your new system running.
What Is a Boiler Installation
New boiler fitting is when you have a new boiler installed in your house. Your house will be heated, and you will have hot water with the boiler.
Why Hassle-Free Installation Should Be Guaranteed
Hassle-free installation should be guaranteed because:
Efficiency: Your boiler would be running efficiently and using less fuel.
Safety: The faulty installation will become a safety feature, such as a fault or a gas leak.
Comfort: It heats your home and your hot water.
Money Saving: It avoids unnecessary cost or delay.
The tips in the following pages of this book will make it simple for you.
Step 1: Select the Perfect Boiler
The first thing you need to do if your new boiler is being installed is select the right one for your home. There are three fundamental boilers: combi boilers, system boilers, and conventional boilers. They belong to another category, so you need to select the one that will be appropriate for your home.
How to Select the Proper Boiler:
Combi Boilers: Ideal for small or terraced houses. Heat water as and when needed, no tank required.
System Boilers: Ideal for large houses. It can feed two or more taps at the same time and is ideal for houses with two or more bathrooms.
Regular Boilers: Ideal for houses with very high hot water demands. Requires a hot water cylinder and a cold water cylinder.
Once you’ve got that out of the way, you can go to step 2.
Step 2: Get a Gas Safe Registered Engineer
Step two is getting someone qualified to fit your boiler. Spend money on a Gas Safe Registered Engineer. Your boiler will be fitted properly and safely this way.
What Does a Gas Safe Engineer Do
Fit the Boiler: The engineer will install your new boiler and connect it to your water and gas supply in your property.
Safety Test: They will conduct a safe test of the boiler so that you can be sure it’s safe to use.
Issue a Gas Safety Certificate: Once installed, the engineer will provide you with a certificate to ensure the work was done safely.
Have only a Gas Safe Registered Engineer install your boiler, only for safety reasons.
Step 3: Remove the Old Boiler
In case you are replacing an old boiler with a new boiler, this initially needs to be removed. Your engineer will dismantle this for you. He will remove your old boiler safely and drain it before installing the new one.
Why Do We Have to Do This Step?
The engineer will actually remove the existing boiler in the best manner possible as well.
Step 4: Installing the New Boiler
It is simple to do, but it should be done in a way that ensures the boiler is in its optimal condition.
New Boiler Installation Instructions:
Install Boiler: The boiler will be installed where it will stay.
Secure the Gas: The boiler will be held in place by a gas pipe.
Step 5: Trial the Boiler and Inspect the System
Once the boiler has been fitted, the engineer will trial it. This is to ensure they are all working and properly fitted.
What the Engineer Will Do:
Inspect Water Pressure: They will check that there is adequate water pressure.
Leak Testing: The engineer inspects that there are no leaks in the supply of water or gas pipe.
Test Heating and Hot Water: They will test the heating and ensure hot water is operational.
Step 6: Complete the Forms
Your engineer will give you the forms you’ll require when they complete installing it:
Gas Safety Certificate: To ensure your boiler is safely installed
Warranty: New boilers usually have a guarantee. Your engineer will outline how long and what it covers.
Instruction Manual: This instruction manual will take you through how to use and service your boiler.
Keep this document in a safe place in case you ever need to refer to it.
Step 7: Register the Boiler with the Manufacturer
You must register your new boiler with the manufacturer. This keeps your warranty active.
Why Do You Need to Register?
Warranty: Registration of your boiler will ensure your warranty stays active.
Safety Recalls: Your boiler will remind you of safety recalls.
Step 8: Fit the Boiler Settings
The engineer will fit the boiler for you. The temperature will be set, and you will be shown
how to use it.
Boiler Settings Tips:
Set the Temperature: Leave this to the engineer. Best of all, it should be between 60°C and 70°C so that it will be energy efficient.
Set a Timer: If you’ve got a timer fitted on your boiler, this implies that you can heat your home only as and when needed. This is an energy-saving system.
Final thought
Getting a boiler installed doesn’t have to be intimidating or overwhelming. If you follow these steps, you can get your new boiler installed and fitted.Choose touch of heat to install boiler for your house, have it installed by a Gas Safe Registered Engineer, and do all the steps so everything is working properly.
With some minimal planning and some professional advice, your new boiler will be up and running in the future to warm and supply hot water.
Frequently Asked Questions (FAQs)
How long does boiler fitting take?
Boiler fitting will take 4-8 hours, depending on the boiler type and whether it’s a replacement boiler or not.
How much does a new boiler fitting cost?
It also depends on the one that you purchase. It is £1,500 to £3,500 fitted.
Do I fit a boiler myself?
No, you will need a Gas Safe Registered Engineer to fit your boiler. Fitting your boiler incorrectly can be dangerous.
How long will my boiler last?
Your boiler will last 10 to 15 years, depending on servicing and model.
When do I know that I need a new boiler?
Signs in the direction of the requirement for a replacement boiler are frequent boiler failures, no heat, and an older boiler (over 10-15 years).